Home > Hard Drive > Primary HDD Plugged In SATA Slave Port

Primary HDD Plugged In SATA Slave Port

Contents

After playing with it awhile, I found that if I pulled my EIDE Promise Card out and connected the EIDE drives back into the MB that everything detected and my system The W2K also detected the new drive when I try check in the ‘device manager'.However, there isn't one WD SATA HD in the explorer. Oh yes and too many fans trust me about the power supply problems I'm removing some fans so I hope that I don't have to replace my power supply, mixing sata Great step backwards MS. Check This Out

Your computer should see and read your drivejust fine. Using cable select worked out great. Just a suggestion. Some SATA drives do have a jumper which controls the speed of the SATA drive itself, but you do not need to worry about anything related to master, slave or cable http://www.sevenforums.com/hardware-devices/141800-primary-hdd-plugged-sata-slave-port.html

How To Slave A Sata Hard Drive

But when the secondary HDD is connected, to either the SATA port after your primary connection, or another SATA port, you can't even boot up to see the Splash Screen? And now the new sata drive does not know you have a burner? I put in a new motherboard recently and couldn't figure out why I could no longer access my IDE HD.

Reply Jimmy says: December 1, 2008 at 8:49 pmThanks, I was having an issue initializing my second SATA hard drive. I am certain I have your answer, remove the pins on your ide drive, this should work, it did for me. After finding your article, written so I could understand it, I gained the confidence I needed to do it. How To Connect Two Sata Hard Disk In One Pc Hope this helps someone! 0 Luke The Press 10 Years Ago Hi all.

the c drive that im using now as like no memary some one told me to stick them in my d/cd or my e/dvd/cd drive to keep them out of my Slave Hard Drive Your step by step made the Job so much better!!Thank You!! Thank you for helping us maintain CNET's great community. http://www.pcadvisor.co.uk/how-to/pc-upgrades/how-slave-sata-drive-3461780/ also i've updated the bios drivers and according to other forums should have stopped the Sata troubles.>ive tried setting the IDE to primary slave and cable select but none have changed

Especially from WinXP 32bit to Vista 64bit. Sata Master Slave Connect the data and power cables so that you can use the drive temporarily to copy data from it to the new drive.If you are adding a drive and will continue So that it is not reading that why it is not recognising. The master hard drive is a seagate sata hard drive.

Slave Hard Drive

I've discovered that if i set it to "IDE Only" - I can get it to detect the IDE, but thenno SATA! IDE (sometimes referred to as ATA or PATA) hard drive controllers use the concept of Master and Slave ports, so: M = Master S = Slave One Master and Slave port How To Slave A Sata Hard Drive Steps 1 Check if you need the IDE (parallel ATA) or Serial ATA. How To Install A Second Sata Hard Drive the bios is not set to ide emulation mode, btw. –user1441998 Dec 15 '14 at 3:35 Unfortunately your motherboard's manual is going to be the best documentation, and as

Tell them that you believe repair should be fair, affordable, and accessible. his comment is here I am going to power off for a minute and double check my cables and all, but my BIOS did not show the Barracuda after post when I just reconnected the Don't have to unplug it, nothing like that. Reply Jon Amoncio says: February 12, 2008 at 3:12 amMy motherboard was crashed and need to be replaced. Master Slave Hard Drive Setup

Thanks alot. My OS is on my SATA hard drive and when I plug in my EIDE maxtor 160 GB HD the system trys to boot from it. You shouldn't have any problems using the converted drive as a slave. this contact form D+ Reply Stefen Kaur says: November 11, 2008 at 12:50 pmI have a question.

NIce to see some floridians.Chaz Reply Tyler Thompson says: November 1, 2007 at 11:09 pmChaz, please register on our forums for more specialized help. Second Hdd Not Detected Windows 10 The red & white audio cable are working fine and I'm getting all of the audio but there is not yellow port on my new tv for the N64's yellow ... SATA drives have a thinner cable and no jumpers to worry about. 2 Make sure you have room for an extra hard drive, here's one way to do this: Restart your

My primary was a SATA and 2nd hd bay was an IDE.

I need the old drive in order to run the image software, as I don't have a boot CD or the windows disks on hand. Don't force them.If you need a separate controller card, install it now into any unused motherboard slot. I changed new SATA cable,power cable and connected after reboot it is getting hang over before starting the CMOS BIOS screen(At Intel mother board screen shot). How To Install A Second Hard Drive Windows 10 The Netbook brand may be not a well-known brand, "ChiliGreen Netbook" model "Neo", the Netbook comes with Windows XP Home edition.

For some people, such sketches help to put everything back when you are done.If you are replacing your old hard drive, remove the cables from the old drive. Answer this question Flag as... So, if anyone has any ideas I would be more than happy to hear them. navigate here Captain :icon_idea: Hi, so I think I know what you're going through...you installed a new sata drive and disconnected the old ones after making the new one the boot, correct?

So my question to the world is can I put the harddrive into another computor to restore lost files and possibally benifit from 1 computor - 2 hard drives.